Preparing your own low cost A+B generic hydroponic nutrients at a small scale from raw salts

linkedinrssyoutubeinstagram
image_pdfimage_print

In a recent post about the cost of custom hydroponic nutrients, I talked about the cost of preparing nutrients equivalent to those of a commonly used brand (general hydroponics Flora series) at a small scale. We saw that the cost savings are not very significant when doing this with small amounts of salts, given that the cost of the salts only drops significantly at larger scales. However there are low cost alternatives to prepare viable hydroponic solutions. In today’s post I want to write about the DIY preparation of hydroponic nutrients and how you can do this from raw salts to arrive at a generic formulation that you can use for flowering plants.

Generic A+B formulation prepared using

The formulation shown above is meant to be a low cost formulation that is close to a Hoagland solution in as many nutrient concentrations as possible, using as few inputs as possible. The concentrated solution is meant to be prepared in distilled water and it is meant to be used in RO/distilled water as no mineral contributions from the incoming water have been taken into account for its making. The solution is prepared at a 250:1 concentration factor, meaning that a gallon of A and a gallon of B can be used to prepare 250 gallons of final nutrients. This is a concentration factor pretty similar to that of the General Hydroponics Flora series, with an intended dosage of around 15mL/gal of A + 15mL/gal of B. At this dosage the EC is expected to be around 2.2 mS/cm (but this should be experimentally determined!). With 250mL of concentrated solution you can prepare up to 62.5L of final solution (~16.5 gallons).

Note that I have decided to use a “chelated nutrient mix” instead of preparing a solution adding micros one-by-one, as this is not very convenient for people new to nutrient solution preparation, plus, some micros are only available in relatively larger quantities that are unnecessary to store for someone who is only interested in the preparation of small amounts of nutrient solution. The above preparation has a cost of around 25 USD/(gal A+ gal B), which is less than one third the cost of one gallon of Flora series. This cost will be significantly lower if you buy the fertilizers in larger quantities and/or if you buy all the micros and weight them independently.

To prepare this accurately at a small scale – as shown in the image above – you will need the following materials and chemicals:

You can follow this process to prepare the nutrients:

  1. Prepare a clean and dry 250mL beaker, wash with distilled water (no soap)
  2. Weight each raw salt on your scale, transfer to the beaker (use distilled water as necessary to ensure everything is transferred)
  3. Add more water and heat – if necessary – to ensure everything is dissolved (add less than 200 mL of water)
  4. Transfer the liquid to the volumetric flask (use distilled water as necessary to ensure everything is transferred)
  5. Take to the final volume using distilled water and homogenize
  6. Transfer to the final storage container

I have also made a video to show you how this entire preparation process is carried out, which I will be sharing shortly! Note I used a potassium sulfate I had previously purchased, which was of significantly low purity (mined potassium sulfate), the link above is for a refined potassium sulfate source, which should give you significantly less problems than it did for me and lead to higher quality solutions (my B solution was cloudy and contained some solids, which were impurities from the potassium sulfate).

If you want to prepare these solutions at a larger scale, then you will face other problems. For example how to accurately measure the final volume of these solutions. Lines in tanks and buckets are terrible volume indicators, flow meters also are also not enough since the salts take a very significant amount of the volume as well (remember we care about the volume of water+salts!). How to properly mix, homogenize, heat and dissolve larger amounts of solution is also not trivial. These are all problems we will be discussing in future posts and videos!

Facebooktwitterredditpinterestlinkedin

5 Comments

  • Jaspreet
    October 15, 2020 @ 1:29 pm

    One confusion still in my mind, when we design our recipe do we take elemental form of the nutrient like (P) (K) or should we take P205 and K20 form??

    Also, the total ppm which are calculated in your software does not match the PPM on my instrument in reservoir?

    But when I covert the salts in P2O5, K20 and So4 and Mgo then the ppm calculation matches the instrument reading.

    Likewise, the phosphorus in elemental (P) form when converted to p2o5, then ppm has huge difference, it completely deviates from my requirement targets and so is for Sulphur (S) to sulphate.

    all the salts are lab grade.

    Kindly guide.

    Thanks

    • Jayakar Reddy
      January 30, 2021 @ 1:56 pm

      Sir please I want nutrient farmula all crapes in Indian climate (I want nutrient PDF files)

      • admin
        January 30, 2021 @ 2:20 pm

        Thanks for writing. Custom formulations are not provided for free. Please use the form’s contact page describing your case so that I can give you a quote for the formulation of your nutrients.

  • Hydroboy
    April 3, 2021 @ 6:31 am

    Hello Dr. Fernandez,
    I watched your video, it simplifies preparation by using customhydro micronutrients.
    However, I can not find in my area the chelated customhydro. I tried entering the peter’s stem micro in the database.
    I’m getting high Cu and Zn in the result when hydrobuddy calculates it,
    Is there are a general table that shows recommended range of micronutrient elements that I can use as a guide?
    Thank you and hoping for more videos like this one.

Leave a Reply to Hydroboy Cancel reply

Your email address will not be published. Required fields are marked *

Subscribe Today!
Receive our FREE blog post updates and monthly newsletter
Thanks for signing up. You must confirm your email address before we can send you. Please check your email and follow the instructions.
We respect your privacy. Your information is safe and will never be shared.
Don't miss out. Subscribe today.
×
×
WordPress Popup Plugin