How to make an organic hydroponic nutrient solution


Hydroponic nutrients are usually made with synthetic chemicals that come from industrial processes. While these chemicals are usually of a higher purity than those mined or obtained from animal or vegetable resources, it also means that these products contain no microbes or bio-stimulants and their origin implies they cannot be used in organically certified growing operations. Growers who want a more organic approach might still want to use hydroponic solutions, but traditional hydroponic fertilizers cannot be used due to the fact that they lack many of the traits desired in an organic fertilizer. In this post, I will show you how you can create a complete hydroponic solution from scratch using only OMRI-approved raw materials.

This seal is given to products that have been approved by the OMRI organization, which certifies which products can be used in organic culture

OMRI nutrient sources

A complete hydroponic solution should provide all substances that are necessary for plant growth. This means we need to provide nitrogen, phosphorus, potassium, magnesium, calcium, sulfur, iron, zinc, boron, copper, molybdenum, and manganese. Furthermore, we need to ensure that all of these nutrients are provided in forms that are available for the plants. This means we need to find sources that contain all the elements we need and then create a process that makes all of these nutrients adequately bioavailable. The following are the nutrient sources that we will be using, all of them are OMRI listed:

Please note the amazon links below are referral links. This means that I get a small commission when you choose to buy the products through these links, at no extra cost to you.

Mixing the solution

This solution cannot be created in a concentrated form. This means we will be preparing a solution that will be fed directly to plants. However, since many of the inputs contain a lot of insoluble materials – due to their origin – there will need to be a filtration process in the end. This filtration step is necessary if you want to avoid problems dealing with the clogging of irrigation lines, in case you want to feed this into a regular irrigation system. If you want to hand water directly, then you can avoid this filtration step.

Since the solution is not concentrated, the amounts to be weighed can be small for some of the materials. For this reason, I advise you to prepare at least 100 gallons of solution, so that you don’t require to weigh very small amounts of material. This will help keep the errors due to measurements low. To make this preparation you will need the following materials:

To prepare the solution (100 gallons), follow these steps:

  1. Add 50 gallons of water using the flow meter. Ideally use RO water, but you can use tap water as well if that is not possible.
  2. Weigh and add all the ingredients per the table below.
  3. Add another 50 gallons of water using the flow meter.
  4. Place the air pump inside the solution and switch it on.
  5. Maintain constant aeration for at least 15 days. Do not use it before this time has passed.
  6. After 15 days have passed, filter the solution to use in irrigation lines or use directly to hand water. Keep air flowing through the solution even after the 15 days have passed.
  7. The solution might also become basic during this process, if necessary, you can bring the pH of the solution down with citric acid before watering plants.
Bark compost 190
Copper sulfate0.15
Corn Steep Liquor330
Ferti-Nitro Plus220
Iron Sulfate4
Magnesium sulfate190
Manganese Sulfate1
Potassium Sulfate136
Seabird Guano265
Zinc Sulfate0.10
Table of ingredients to weigh. Masses are in grams.

The reason for the long wait

Plants ideally require nitrate in order to grow, the above inputs do not contain nitrate in appreciable amounts but mainly organic nitrogen sources. In this and this previous posts, you can learn more about organic nitrogen and why it is not ideal to use this in an unprocessed manner in a hydroponic crop. When you irrigate with organic nitrogen, most of the nitrogen will go unused and significant time will need to pass in the root zone for it to become available. The organic nitrogen decomposition process can also destabilize the pH of the root zone, making it harder for plants to properly absorb nutrients. By carrying out this process outside of the root zone, we make it easier on the plants, as we feed a pre-digested solution that is rich in available nutrients and microbes. The Seabird Guano and Bark compost, both provide the microbe inoculations necessary for the nitrogen decomposition process to take place. Oxygen, which we continuously pump into the solution, is also key to this process. The CSL and the Ferti-Nitro Plus will provide the organic nitrogen sources that will be decomposed.

This solution also contains a significant amount of amino acids. Although most of these amino acids will be converted into more readily absorbable nitrate through the digestion process, a small amount will be left undigested, which will lock onto the heavy metal ions. This will help prevent precipitation issues and provide the plant with organically derived chelates.

Also note that no specific molybdenum input is included. This is because it is present as an impurity in the corn steep liquor at a high enough concentration, so its explicit addition is not required.


The above solution should fully replace a traditional hydroponic solution, using only OMRI-approved materials. The final concentrations of nutrients should be spot on for the healthy development of most small and large plants. The solution will also contain a lot of microbes and bio-stimulants, which will also help plant growth. Of course, the final character of the solution will depend on the temperature of the digestion, the amount of aeration present, and the nature of the inputs used (as OMRI inputs have a significant amount of variability due to their sourcing). It might take a few tries to adjust this process to your particular conditions. Note that the above solution is intended to be used with soilless media that has not been amended, as it should provide all nutrients required for plant growth.

Did you prepare the above solution? Leave a comment telling us about your experience!



  • Matt Baker
    June 28, 2021 @ 10:33 pm

    Hi. I am finding your articles to be very interesting. Thank you for taking the time to write them up!

    I am very interested in your organic recipe. I would like to use it once or twice a week to supplement top dressing in an indoor living soil setup. I am curious about your experience with this recipe and if you have any direct experience growing plants with it? Have you done a laboratory nutrient analysis on the solution?

    Thank you again,

    Matt Baker

  • Braden Montgomery
    September 29, 2021 @ 8:00 pm

    Is it possible to use a commercial inoculate such as EM-1 instead of bark? Would it be a faster turn around time for larger set ups as a fermented extract?

    • admin
      September 30, 2021 @ 7:23 am

      I have never tried a commercial inoculate, so I don’t know if it would work or be faster. You would need to try.

  • Earuma
    November 20, 2021 @ 3:04 am

    What about calcium?

    • admin
      November 20, 2021 @ 6:45 am

      Seabird guano contains significant amounts of Calcium. Tap water will also supply around 30-50ppm of additional Ca in most places in North America. If you want you can also supply additional Ca with OMRI Gypsum (although gypsum is considered “insoluble” it is soluble enough to supply up to 400 ppm of Ca).

  • Allen Brown
    March 21, 2022 @ 11:14 am


    I am curious if you have a recommendation to improve microbial populations and associated biostimulants while still using salts. We do not have the water storage capacity to have 15 days plus of nutrients on hand constantly but would like to feed the microherd and help them flourish.


  • Benny Thompson
    August 5, 2022 @ 8:45 pm

    Have you tried this formula? I’ve been running commercial vermiponic operation in San Diego for 3 years… you should never use citric acid to change pH. It’s anti-microbial and it breaks down in like 12 hours and the pH will bounce right back. Also, OMRI allows phosphoric acid for aquaponic pH adjustment, but not for phosphorus deficiencies.

    • admin
      August 7, 2022 @ 6:28 pm

      Thanks for writing. I have indeed tried it, however it is true that I have never had to lower the pH if enough time in the fermentation has passed. Note also that the citric acid is not meant as a way to constantly adjust the pH, but just to adjust the formulation once after preparation. I do agree that citric acid is not a viable solution for the continuous adjustment of any solution in hydroponics.

      I also have to say that I have since improved on the organic formulations a lot (deviating substantially from that proposed in this post). You can checkout my instagram for some of my latest results in organic formulations on leafy greens.

Leave a Reply

Your email address will not be published.